Talk to an Off-Road Enthusiast
1.888.385.5036
Chat For Support On Your Order
Black November · 15% off all Cali Raised branded items · Shop now › 15% off Cali Raised · Shop Black November ›

Lead Time: 0-4 Weeks

Trail Edition Bolt On Rock Sliders for 2010-2024 (5th Gen) Toyota 4Runner

Trail Edition rock sliders (also called rock rails) for the 2010-2024 (5th Gen) Toyota 4Runner. They bolt to the frame, angle up 20 degrees for more clearance on rocks and ledges, and protect your rocker panels and doors. Fits KDSS and non-KDSS trucks, installs in about 1 to 2 hours with no drilling, and ships free from our shop in Fort Worth, Texas. Want a flat step instead? See the Step Edition for the same truck.

Read the full overview and specs
ON SALE

From $773.49 $909.99

See payment options
Product Options
Kick Out No Kick Out
Raw Steel Powder Coat Bedliner
Fits:Toyota 4Runner 2010-2024
Secure checkout · Shop Pay & all major cards
Trail Edition Bolt On Rock Sliders for 2010-2024 (5th Gen) Toyota 4Runner $773.49

Before you buy

Popular setup
Kick out, powder coat slider.
Options explained
Kick out or no kick out?
Kick out vs no kick out rock sliders side by side. Kick out has an angled rear end, no kick out is straight.

Kick out angles the back of the slider out, in front of the rear tire, so the back of your truck doesn't get pinned on rocks. No kick out runs straight for a clean look. Same price either way.

Full kick out guide

Which finish should I pick?
Rock slider finishes: raw steel for custom color, black powder coat recommended for the slider, bed liner recommended for the top plate.

Raw steel: bare steel that will rust if left uncoated. Paint or coat it right away. Powder coat: black, ready to bolt on. Bedliner: rugged textured finish with extra grip.

Full coatings guide

Fitment
  • 2010–2013 4Runners must remove the Rock Trim Panel for sliders to fit properly.
  • Limited and TRD Sport with X-REAS: fits only after the X-REAS system and side moldings are removed.
  • Not compatible with Lexus GX.

Trail Edition Sliders for the 5th Gen 4Runner

Each slider mounts to a full frame plate with front and rear clamps, so a hit on the rocks goes into the frame instead of the body. The tubing is fully gusseted, and with no top plates the Trail Edition stays tucked tight to the body and out of the way on technical trails.

Every set is designed and fabricated in-house and covered by a 2-year warranty, powder coat included.

Specs

Trail Edition rock sliders for 2010-2024 Toyota 4Runner: specs
Fits2010-2024 Toyota 4Runner (5th Gen), KDSS and non-KDSS
Tubing1.75-inch DOM, .120-inch wall
MountingFull frame plate, front and rear clamps
LoadHolds the full weight of the vehicle; works as a jack point
Length64 inches
WeightAbout 90 lb per set
FinishRaw, black powder coat or bedliner
InstallBolt-on, no drilling, 1 to 2 hours
In the box2 sliders, 2 plates, 2 clamps, Grade 8 hardware
ShippingFree, FedEx Ground in 2 boxes
Warranty2 years, powder coat included

Trail Edition or Step Edition?

Trail Edition vs Step Edition for the 2010-2024 Toyota 4Runner
Trail Edition (this page)Step Edition
Angle20 degrees up, tucked to the body0 degrees, flat step
Top platesNoneOptional filler plates to stand on
Weight per setAbout 90 lbAbout 100 lb
Best forTrail clearance, technical terrainDaily driving, passengers, roof access

Questions

Will these rock sliders fit my 2010-2024 4Runner?

Yes, they fit every 2010-2024 (5th Gen) Toyota 4Runner, with or without KDSS. On Limited and TRD Sport models with X-REAS, they fit only after the X-REAS system and side moldings are removed. On 2010-2013 trucks, remove the Rock Trim Panel first. They do not fit the Lexus GX460 or the 2025+ 4Runner.

What tubing are these 4Runner sliders made from?

1.75-inch DOM tubing with a .120-inch wall, fully gusseted. DOM (drawn over mandrel) is cold-drawn after forming, which gives it a smoother, more even wall and higher strength than HREW (hot rolled electric welded) tubing, the lower-cost option some sliders use.

Can these sliders hold the weight of my 4Runner, and can I jack from them?

Yes. They bolt to the frame with a full frame plate and front and rear clamps, so they carry the weight of the 4Runner, and you can lift the truck from the slider with a jack.

Should I get the Trail Edition or the Step Edition for my 4Runner?

Get the Trail Edition if clearance on rocks and ledges matters most: it angles up 20 degrees and tucks tight to the body, with no top plates. Get the Step Edition if you want an everyday step for passengers or roof access: it is flat (0 degrees) with optional filler plates. Both bolt on and come with or without a kick out.

Are these rock sliders bolt-on, and how long does install take on a 4Runner?

They are 100% bolt-on to the factory frame with Grade 8 hardware, with no welding, drilling or cutting. Install takes about 1 to 2 hours. Each set weighs about 90 lb, so a helper or jack stands make it easier.

Will they work with my 4Runner gas tank skid plate?

Yes. With the factory gas tank skid plate, the slider goes below it. With a Cali Raised LED gas tank skid plate, the slider goes above it and the skid plate goes underneath.

How far do these sliders stick out from my 4Runner?

Measured from the pinch weld (the seam under the doors), the Trail Edition sits about 8 5/8 inches out with kick out and about 6 1/8 inches out with no kick out, give or take 1/2 inch. Kick out sits farther out because the rear of the slider angles out in front of the rear tire.

More questions? Call 888-385-5036 or email support@caliraisedled.com.

Installation

Read installation steps

How to Install 2010-2024 Toyota 4Runner Rock Sliders

Watch the video, then follow the written steps below to bolt Cali Raised LED Rock Sliders onto your 2010-2024 Toyota 4Runner (5th Gen). These steps cover both the Step Edition (0-degree flat step) and the Trail Edition (20-degree angle), on KDSS and non-KDSS trucks.

Installation steps

Before you start: A helper or jack stands make it much easier to hold the slider against the frame. Tools: 13 mm socket and wrench, plus 9/16 and 3/4 sockets and wrenches. An impact wrench helps.

  • Step 1: Set up the frame bolts (by hand). On each frame bolt, slide on the lock washer first, then the flat washer, then the bolt goes through the frame plate into the frame.
  • Step 2: Remove the brake line brackets (socket). On the passenger side, remove the two brake line brackets from the frame.
  • Step 3: Hang the passenger slider (jack stands or a helper). Lift the slider up to the frame and start one bolt toward the center, just a few threads, to hold it in place.
  • Step 4: Start every bolt loose (by hand). Thread a few turns on every remaining bolt before you tighten any of them, or some holes may not line up. The two longer bolts go in the holes where the brake line brackets were. Extra holes in the frame plate are for other model years, so leave any hole with no matching frame hole empty.
  • Step 5: Install the passenger side clamp (socket and wrench). On the inside of the frame, stack the hardware in this order: bolt, washer, aluminum spacer, clamp, washer, then the lock nut. Keep the clamp toward the outside of the truck so it does not fall inside the frame, then spin it into place.
  • Step 6: Level and tighten the passenger side (socket, impact wrench). Tighten the bolts while keeping the slider level and pressed up against the frame. The holes are slotted, so check the slider as you go.
  • Step 7: Hang the driver slider (jack stands or a helper). Repeat Steps 3 and 4 on the driver side. If you have the factory gas tank skid plate, the slider goes below it. If you have a Cali Raised LED gas tank skid plate, the slider goes above it and the skid plate goes underneath.
  • Step 8: Install the driver side frame plate mounts (socket and wrench). Line up the holes on the two frame plate mounts with the holes on the frame plate and start those bolts against the frame.
  • Step 9: Level and tighten the driver side (socket, impact wrench). Tighten every bolt while keeping the slider fully level and pressed against the frame.

Final check: Make sure every bolt is tight, both sliders sit level and flush against the frame, the brake lines are clear of the sliders, and any skid plates are seated correctly. Coat raw steel sliders right away. Questions? support@caliraisedled.com or 888-385-5036.

  • 5 stars: 4 (100%)
  • 4 stars: 0 (0%)
  • 3 stars: 0 (0%)
  • 2 stars: 0 (0%)
  • 1 star: 0 (0%)
R
Robert D.

Great rock sliders with straight forward install.

Thanks Robert, and thanks for the photo! A straightforward bolt-on install is what we aim for with the Trail Edition on the 5th Gen 4Runner. – Jake at Cali Raised LED

L
Loren B.
Awesome Rock Sliders. Great product and solid!

Installed Trail Edition sliders on a 2022 TRD Off Road. Super easy to install, rock solid and plenty of support. Already took some hits and proceed the body and chassis.

R
Richard S.
Good solid products with style.

Good solid products with style. Helpful customer service.

J
Justin G.
Great quality product!

Let me just first say ... thank you! These are GREAT QUALITY and I can’t wait for them to save my butt from very expensive repairs that I would endure without them!

Just a side note and not a big deal ... YouTube has everything on earth ... but the installation video is lacking ... I believe you should have focused more on the non obvious stuff ... like the brackets (which I don’t recall mentioned at all on the drivers side) ... and the special clamp bolts on the passenger side that were mentioned ... but never really shown what needed to happen. Just my .02¢. Like I said ... YouTube is a great thing and just found it on another channel ... no biggie

I’m sure I will love these ... I am incredibly impressed with your price ... your communication and appreciation conveyed through that communication and how fast they arrived! You’ve got me as a customer for sure now ... my first experience with you ... and 5 out of 5 team! Thank you!

Recently Viewed