Kick out angles the back of the slider out, in front of the rear tire, so the back of your truck doesn't get pinned on rocks. No kick out runs straight for a clean look. Same price either way.
Raw steel: bare steel that will rust if left uncoated. Paint or coat it right away. Powder coat: black, ready to bolt on. Bedliner: rugged textured finish with extra grip.
Each slider mounts to a full 3/16-inch steel frame plate with front and rear clamps that hook over the frame, so a hit on the rocks goes into the frame instead of the body. The tubing is fully gusseted, and with no top plates the Trail Edition stays tucked tight to the body and out of the way on technical trails.
Every set is designed and fabricated in-house and covered by a 2-year warranty, powder coat included.
| Fits | 2005-2023 Toyota Tacoma (2nd and 3rd Gen), Access Cab and Double Cab short or long bed |
|---|---|
| Tubing | 1.75-inch DOM, .120-inch wall |
| Mounting | Full 3/16-inch frame plate, front and rear clamps |
| Load | Holds the full weight of the vehicle; works as a jack point |
| Length | 81 inches (Access Cab and short bed), 94 inches (long bed) |
| Weight | About 100 lb per set |
| Finish | Raw, black powder coat or bedliner |
| Install | Bolt-on, no drilling, 1 to 2 hours |
| In the box | 2 sliders, Grade 8 hardware |
| Shipping | Free LTL freight |
| Warranty | 2 years, powder coat included |
| Trail Edition (this page) | Step Edition | |
|---|---|---|
| Angle | 25 degrees up, tucked to the body | 0 degrees, flat step |
| Top plates | None | Optional top plates to stand on |
| Weight per set | About 100 lb | About 120 lb |
| Best for | Trail clearance, technical terrain | Daily driving, passengers, roof access |
Yes. They fit 2005-2023 (2nd and 3rd Gen) Tacomas in Access Cab, Double Cab short bed and Double Cab long bed, including Base, SR, SR5, TRD Sport, TRD Off-Road, Limited and TRD Pro. Select your cab and bed when you order. They do not fit the 2024+ Tacoma.
1.75-inch DOM tubing with a .120-inch seamless wall, on a full 3/16-inch carbon steel frame plate. DOM tubing is drawn over a mandrel after welding, so its size and wall are more uniform than plain welded (HREW) tubing.
Yes. Each slider bolts to the frame through a full 3/16-inch steel frame plate with front and rear clamps that hook over the frame, so it can hold the weight of your Tacoma and works as a jack point.
Get the Trail Edition if you want more clearance: it angles up 25 degrees, stays tucked to the body, has no top plates and weighs about 100 lb per set. Get the Step Edition if you want a flat 0-degree step for daily driving, passengers and roof access. It offers optional top plates and weighs about 120 lb per set.
Yes. They bolt on with no drilling, and install takes about 1 to 2 hours. At about 100 lb per set, plan on a helper or a floor jack to hold each slider. The only trim is a small notch in the passenger-side plastic wiring cover so it fits over the slider gusset.
Yes. The same sliders fit 2005-2023 Tacomas and install the same way. On 2016 and newer trucks (and select models) you unbolt and hang the frame black box during install, and 2nd Gen two wheel drive trucks use four frame bolt positions instead of three.
Measured from the pinch weld (the seam under the doors), the Trail Edition sits about 6 5/8 inches out with kick out and about 3 3/4 inches out with no kick out, give or take 1/2 inch. The 25-degree angle keeps it about 3 inches tighter to the body than the Step Edition. Kick out sits farther out because the rear of the slider angles out in front of the rear tire.
More questions? Call 888-385-5036 or email support@caliraisedled.com.