Is there a Cali Raised LED cat shield for the 2007-2021 Tundra?

No. This shield is made only for the 2022+ (3rd Gen) Tundra. Cali Raised LED does not currently make a catalytic converter shield for the 2007-2021 Tundra.

Can a thief still cut through the shield?

Given enough time and a battery-powered grinder, any shield can be cut, so no shield is theft-proof. The 12-gauge stainless and tamper-resistant security bolts turn a quick, quiet theft into a slower, louder job, which is often enough to send a thief to an easier target.

Cali Raised LED catalytic converter shield for the 2022+ Toyota Tundra, driver- and passenger-side 12-gauge 304 stainless guards.

Catalytic Converter Shield For 22+ Toyota Tundra - installed view | Cali Raised LED

Catalytic Converter Shield For 22+ Toyota Tundra - close-up detail | Cali Raised LED

Catalytic Converter Shield For 22+ Toyota Tundra - lifestyle photo | Cali Raised LED

Catalytic Converter Shield For 22+ Toyota Tundra - angled view | Cali Raised LED

Catalytic Converter Shield For 22+ Toyota Tundra - hardware detail | Cali Raised LED

Catalytic Converter Shield For 22+ Toyota Tundra - product overview | Cali Raised LED

Catalytic Converter Shield For 22+ Toyota Tundra - finish and color options | Cali Raised LED

Catalytic Converter Shield For 22+ Toyota Tundra - mounting bracket detail | Cali Raised LED

Catalytic Converter Shield For 22+ Toyota Tundra - rear view | Cali Raised LED

Catalytic Converter Shield For 22+ Toyota Tundra - packaging contents | Cali Raised LED

Cali Raised · Ships from our Texas Facility

Anti-Theft Catalytic Converter Shield for 2022+ Toyota Tundra

MPN: CR3943

Protect your 2022+ Toyota Tundra from catalytic converter theft with a heavy-duty shield engineered for vehicle-specific coverage. This bolt-on system covers the driver- and passenger-side catalytic converters while maintaining airflow around the exhaust system.

Protect Your 2022+ Toyota Tundra’s Catalytic Converters

Catalytic converters are valuable, accessible, and expensive to replace. This catalytic converter shield creates a strong physical barrier around both converters, helping deter theft without interfering with normal vehicle operation.

12-Gauge Stainless Steel Construction

Each shield is fabricated at the Cali Raised LED facility in Fort Worth, Texas from 12-gauge 304 brushed stainless steel. The corrosion-resistant bare stainless finish is built to handle demanding weather, road debris, and off-road conditions.

Integrated ventilation openings allow heat to escape from around the catalytic converters. Do not paint or apply an aftermarket coating to the shield because catalytic converters generate extreme heat.

2022+ Toyota Tundra Fitment

This catalytic converter shield fits the following non-hybrid 2022+ Toyota Tundra configurations:

CrewMax models
Crew Cab Long Bed models
2WD models
4x4 models

Important: This product does not fit Toyota Tundra models equipped with the i-FORCE MAX hybrid powertrain.

Bolt-On Installation With Security Hardware

The shield installs using existing factory mounting locations without drilling or welding. Installation is rated easy, takes approximately one hour, and can be completed at home with the included security tool and a 14 mm wrench.

Watch the official installation video before starting and follow applicable Toyota service procedures when working around factory hardware.

What’s Included

Driver-side catalytic converter guard
Passenger-side catalytic converter guard
Tamper-resistant security hardware
Security installation tool

Before you buy

Other versions: Catalytic converter shields for other trucks
Install: ▷ Install Video
↓ Cali Raised LED installation guide PDF - Catalytic Converter Shield for 2022+ Toyota Tundra (CR3943) Rev B
Install steps on this page
Fitment: Fits non-hybrid 2022+ Tundra CrewMax and Crew Cab Long Bed, 2WD and 4x4.
Does not fit Tundra models with the i-FORCE MAX hybrid powertrain.

SPECIFICATION

FITMENT & COMPATIBILITY

FAQ

Vehicle fitment: 2022+ Toyota Tundra CrewMax and Crew Cab Long Bed models
Drivetrain: 2WD and 4x4
Hybrid compatibility: Does not fit i-FORCE MAX hybrid models
Material: 12-gauge 304 brushed stainless steel
Finish: Bare brushed stainless steel
Manufacturing: Fabricated in Fort Worth, Texas
Installation: Bolt-on using existing mounting locations, with no drilling or welding
Estimated installation time: Approximately 1 hour
Installation difficulty: Easy
Additional tool required: 14 mm wrench
Included: Driver- and passenger-side guards, tamper-resistant security hardware, and security installation tool
Skid plate compatibility: Designed to work with factory, Cali Raised, and aftermarket skid plates; verify clearance with nonstandard aftermarket designs
Warranty: 2-year limited warranty covering manufacturing defects
Warning: Do not paint or apply an aftermarket coating because catalytic converters generate extreme heat
SKU/MPN: CR3943

Compatible vehicles:

2022+ Toyota Tundra CrewMax
2022+ Toyota Tundra Crew Cab Long Bed
2WD and 4x4 models
Non-hybrid models only

Not compatible: Toyota Tundra models equipped with the i-FORCE MAX hybrid powertrain.

Skid plate compatibility: Designed to work with factory, Cali Raised, and aftermarket skid plates. Because aftermarket designs can vary, verify mounting-point and underbody clearance before installation.

Modified trucks: Vehicles with modified suspension components or non-factory crossmembers should verify mounting-point alignment before installation.

1. What 2022+ Toyota Tundra models does this catalytic converter shield fit?
It fits 2022+ Toyota Tundra CrewMax and Crew Cab Long Bed models with 2WD or 4x4. It is designed for non-hybrid models and does not fit i-FORCE MAX hybrid models.

2. Does installation require drilling or welding?
No. The shield uses existing factory mounting locations and does not require drilling or welding. Installation takes approximately one hour and requires the included security tool and a 14 mm wrench.

3. What is included with the catalytic converter shield?
The kit includes driver- and passenger-side catalytic converter guards, tamper-resistant security hardware, and the required security installation tool.

4. What material is the catalytic converter shield made from?
The shield is fabricated in Fort Worth, Texas from 12-gauge 304 brushed stainless steel and is supplied in a bare brushed finish.

5. Will it work with factory or aftermarket skid plates?
It is designed to work with factory, Cali Raised, and aftermarket skid plates. Because aftermarket designs can vary, verify mounting-point and underbody clearance before installation.

6. What warranty is included?
Cali Raised LED branded products include a 2-year limited warranty covering manufacturing defects. Review the warranty policy for complete terms.

Installation

About 1 hour · No drilling · 7 steps · Driver + passenger side

Download PDF

Read installation steps

Catalytic Converter Shield Installation Instructions — CR3943

Install the Cali Raised LED Catalytic Converter Shield (CR3943) on your 2022+ Toyota Tundra using the instructions below. The shield helps deter catalytic converter theft by bolting a 12-gauge 304 stainless guard around each converter, using the existing factory mounting locations.

Fitment and installation time

Fits 2022+ Toyota Tundra CrewMax and Crew Cab Long Bed, 2WD and 4x4, non-hybrid only. Does not fit i-FORCE MAX hybrid models. Trucks with modified suspension or non-factory crossmembers should check mounting-point alignment first. Estimated installation time: about 1 hour. No drilling or welding.

Included in the kit

Driver-side shield (front tab stencilled D) and passenger-side shield (stencilled P), 12-gauge 304 brushed stainless
Two supplied security bolts
Four washers
One included security bit

Tools you supply

Two 14 mm wrenches, or ratchets with 14 mm sockets (one above and one below the cross brace)
A ratchet or driver that holds the included security bit
Helpful, not required: a rubber mallet; penetrating oil if the threads are dirty

Before you start

The install video is shot on a lift. At home, park on level ground and support the truck on jack stands; never work under a vehicle held up only by a jack. Let the exhaust cool completely first. Do not paint or coat the shield; catalytic converters generate extreme heat. Follow applicable Toyota service procedures when working around factory hardware.

Installation steps (driver side first)

Find the two factory bolts. Under the truck, look at the cross brace beside the catalytic converter. Two factory bolts hold it on. That is where the shield hangs.
Loosen both factory bolts. Do not remove them. Back each one out until there is about a 3/8 to 1/2 inch gap under the head. Work one tool from above and one from below the brace.
Hang the shield. Slip the two keyhole slots on the rear tabs over the two loosened bolt heads, then slide the shield up a little so it seats on the bolts.
Start the security bolt. Put one supplied washer on each side of the front tab, then thread the supplied security bolt in by hand until it is finger snug. If the threads are dirty, a little penetrating oil helps. Leave it finger snug for now.
Snug, push up, tighten. With the shield hanging slightly low, snug both factory bolts. Push the shield all the way up against the brace, then tighten both factory bolts firmly; they hold the cross brace on.
Tighten the security bolt. Put the included security bit in your ratchet or driver and tighten the front security bolt until the shield sits tight and does not move. Do not over-tighten. If the hardware will not seat the way it should, stop and email support before you force it.
Repeat on the passenger side. The shield stencilled P goes on the passenger side. Same two factory bolts on that side's cross brace, same order: loosen, hang, start the security bolt with a washer each side, snug and tighten the factory bolts, then the security bolt.

Check your work

Both shields sit flat against the cross brace.
All four factory bolts are tight.
Both security bolts are seated and neither shield moves when pulled.
D on the driver side, P on the passenger side.

Keep the included security bit safe; it is what takes the shields back off.

Need help?

If the hardware will not seat correctly, stop before forcing it and contact support@caliraisedled.com.

Instructions based on the Cali Raised LED CR3943 installation guide, Rev B, September 24, 2026.

Recently Viewed

5 stars: 37 (90%)
4 stars: 3 (7%)
3 stars: 0 (0%)
2 stars: 0 (0%)
1 star: 1 (2%)

Installation on my 2025 Toyota

Installation on my 2025 Toyota Tundra CrewMax 4x4 was simple and straightforward. The installation video by Yota Expedition on YouTube was very helpful. I supported the transmission crossmember support with a bottle jack so that I could loosen (DO NOT REMOVE!) the two 14mm bolts located in that area for attaching the shield. No torque for those bolts was provided, so I checked with my Toyota dealer. They told me to use 31 lbs. , which worked well (but check with Toyota for your particular vehicle. ) I agree with another post that it would be nice if an extra security key for the Torx Head screw was included, because it could easily get lost. I like the fit and look of the shield and recommend it as a deterrent to catalytic converter theft.

Great product! Easy to install

Great product! Easy to install and two outstanding attributes I appreciate, functionality and aesthetics. Highly recommend!

Good price …good product

Install was quick and easy on passenger side of truck but when it came to drivers side I had too remove both cross member bolts In order to get into place it was a tight fit . drivers side was under bent on the press guessing .

Good quality and easy installation.

Good quality and easy installation. :+1:

Catalytic Converter Shield

My friend installed this for me, and he said it was super easy!

SKOOKUM!

These are well made skookum shield. Simple design and excellent fit.

Catalytic covers

A bit difficult to install without a lift, but the product fit nicely and now I have piece of mind that the cats won’t get stolen.
I had a cat stolen on a different vehicle and that was $800 for the cat, sensors and labor so I can only imagine these two cats, sensors and labor, would cost about $2000-2600 to replace, so I was more than happy to pay for these covers.
Now, not having a lift makes install a bit tight, but the key is unscrewing the bolts on the back. Just be careful not to unscrew the bolts all the way and retighten everything tightly.
I do have a skid plate but these covers fit nicely in place, so great job Caliraised for the product!!

Great Shields after modification

Great set of shields. Well made. I had a issue on the driver's side with a edge of the shield touching the 4x4 axle's rubber boot, and needed to contact Cali Shield. They responded quickly and agree to send me a new version. I modified mine and installed them.

The package was delivered with the box smashed driver side was bent and all the hardware was missing

Mike, we’re sorry the Catalytic Converter Shield arrived with shipping damage and missing hardware. We’d definitely like the opportunity to help get this resolved. Please reach out to support email with a few photos of the shield and packaging so our team can review everything and help you from there.

Second purchase

I purchased for my Tacoma 4-5 years back so I had to get a set for my new tundra. Excellent craftsmanship. Beautiful stainless. Super easy to install. Certainly gives me more peace of mind.

Good Fit & Protection

Both sides of the shield installation were straight forward. The crossbar on my 2026 did slide down when I loosened the bolts as others mentioned. The stainless steel washers for the security screws work well, but having them slightly wider would make install even easier. I like that these sit flush under the cats and don't block the trans plug or other service areas. They're constructed well.

Great product

Fit was just like they said. Had installed complete within 30 min.

Excellent quality and fit

Great product. Well made and fits as advertised. One caution, on the 2026 Tundra watch out for the crossmember under the transmission. It will drop slightly when the bolts are loosened even on just one side. I used a floor jack to to push it back into place before the bolts are tightened.

Converter Shield Install

Great product. Well made and fits as advertised. One caution, on the 2026 Tundra watch out for the crossmember under the transmission. It will drop slightly when the bolts are loosened even on just one side. You will have to push it back into place before the bolts are tightened.

Extremely happy with my purchase.

Extremely happy with my purchase. Team installing it had to modify the driver side since I have a 6” lift, the cross member didn’t match up. They made some fab adjustments and it’s installed.

Well made and fits! -

Well made and fits! - was missing stainless steel washers - I had some so not a big deal. When the bolts are loosened on the rear connection point, the support arm that is holding the weight of the transmission needs to be supported. There is some movement and none of the videos or instructions have that note.

Outstanding upgrade to deter these

Outstanding upgrade to deter these rat bastards who rob from us! Thank you guys, excellent product and easy to install!:punch::skin-tone-4::u1F1FA::u1F1F8:

Outstanding product and customer care!

Outstanding product and customer care! I Purchase a catalytic shield for my forerunner and ended up trading it in before I installed it. I purchased a Toyota tundra and I had zero issue with Exchange. The product fit great and installed Easy. Thank you.

Installation was easy. I wish

Installation was easy. I wish they would give a spare lock key - they can get lost very easily.

Great, easy install

Great, easy install

Great quality product and super

Great quality product and super simple install. Definitely worth the price, you will be glad you got them.

24’ Tundra Cat Shield

Fit my 2024 Toyota Tundra Platinum TRD OFF-ROAD V6 (not hybrid) perfectly. 4 stars because the washer they provided is too small for the OEM skid plates. So now I need to be inconvenienced by figuring out what size washer I need for it to fit my skid plate.

Fits well

Fits well

Fantastic product. Very easy to

Fantastic product. Very easy to install. Well worth the price.

Easy install

My second set after I traded in my Tacoma for a Tundra. Easy enough install but watch out for the heat shield on the driver’s side interfering with the shield frame. Just bend the shield back with a large flat blade screwdriver